Quantcast Chapter 4. GENERAL SUPPORT AND DEPOT TESTING PROCEDURES

 

Click here to make tpub.com your Home Page

Page Title: Chapter 4. GENERAL SUPPORT AND DEPOT TESTING PROCEDURES
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home


   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
Figure 3-2. Radio set simulator uhf test generater, alignment test setup.
Up
TM-11-6625-564-45 Maintenance Kits Electronic Equipment MK-731/ARC-51X Manual
Next
Figure 4-1. Matching pads, fabrication details.
TM
11-6625-56445
CHAPTER 4
GENERAL SUPPORT AND DEPOT TESTING PROCEDURES
each chart before proceeding to the chart. Per-
4-1. General
form each test in sequence. Do not vary the
a. Testing procedures are prepared for use
sequence. For each step, perform all of the ac-
by Signal Field Maintenance Shops and Signal
tions required in the Control setting column;
Organizations responsible for general support
then perform each specific test procedure, and
and depot maintenance of electronic equip-
verify it against its performance standard.
ment to determine the acceptability of repaired
electronic equipment.  These procedures set
4-2. Test Equipment and Materials
forth specific requirements that repaired elec-
Required
tronic equipment must meet before it is re-
All test equipment,  material, and other
turned to the using organization. These pro-
cedures may also be used as a guide to test
equipment required to perform the testing pro-
cedures given in this chapter are listed in the
equipment repaired by direct support mainte-
following charts and are authorized under TA
nance personnel if the proper tools and test
equipment are available. A summary of the
11-17, Signal Field Maintenance Shops, and
TA 11-100 (11-17), Allowance of Signal
performance standards is given in paragraph
Corps Expendable Supplies for Field Mainte-
b. Comply with the instructions preceding
nance Shops.
a. Test Equipment.
Technical manual
Federal stock No.
Nomenclature
Charger, Battery PP-1451/U
6625-643-1568
Audio Oscillator TS-421/U
TM 11-6625-200-12
Multimeter  ME-26B/U
6625-646-9409
TM 11-6625-320-12
Voltmeter, Meter ME-30(*)/Ua
6625-669-0742
a Indicates Voltmeter. Meter ME-30A/U. and Voltmeters. Electronic ME-30B/U and ME-30C/U.
b. Materials.
(8) Sheet metal, aluminum, 3/4 x 1-1/2
in., 4 ea.
(1) Resistor, 9.5-ohm, 1/2-watt carbon, 2
ea.
(9) Sheet metal, aluminum, 3/4 x 1-3/4
(2) Resistor, 150-ohm, 1/2-watt, carbon,
in., 4 ea.
1 ea.
(10) Sheet metal, aluminum, 4-1/2 x 1-
(3) Resistor, 5-ohm, 1/2-watt, 1 percent,
3/4 in., 4 ea.
carbon, 1 ea.
(4) Resistor, 600-ohm, 1/2-watt, 1 per-
4-3. lest Facilities
cent, carbon, 1 ea.
Power to Charger, Battery PP-1451/U must
(5) Resistor, 27-ohm, 1/2-watt, 1 per-
be supplied from an external source. Two
cent, carbon, 1 ea.
matching pads must be fabricated; fabrication
(6) Resistor, 123-ohm, 1/2-watt, 1 per-
details are shown in figure 4-1, and the ma-
cent, carbon, 1 ea.
terials that are required are listed in para-
(7) Resistor, 573-ohm, 1/2-watt, 1 per-
cent, carbon, 1 ea.
67

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.