 |
|||
|
|
|||
|
|
|||
| ||||||||||
|
|
 TM 11-6625-564-45
3/16-inch inner diameter, and four
(28) Remove No. 1 idler shaft assembly
(115 through 118). If necessary, re-
sleeve bearings (65, 78, 106, 124)
move retaining ring (115) from No.
have a 1/8-inch inner diameter.
1 idler shaft, remove spring pin
(41) Remove two machine screws (40),
(118), and slide 38-tooth spur gear
two lockwashers (41), two square
(117) off shaft.
spacing posts (127), machine screw
(29) Remove two pivot screws (68) from
(24), l o c k w a s h e r ( 2 5 ) , a n d o n e
solenoid L4 (66), and remove pawl
sleeve nut (102) from lower edge of
rear gear plate (31).
(67).
(30) Remove six pivot screws (two 81, two
(42) Remove captive screw spring (128),
109, two 131) from other three sole-
modified machine screw (125), and
noids (79, 107, 129), and remove re-
lockwasher (126) from each of two
spective pawls (80, 108, 130).
square spacing posts (127).
(31) Remove four pawl springs (89, 94,
(43) Remove two machine screws (92 and
113, 121) from four pawl spring
123), two lockwashers (91 and 122),
guides (90, 93, 112, 120).
and two stud terminals (26 and 39)
(32) Remove two machine screws (1) two
from rear gear plate (31).
fiber washers (2), two ceramic posts
(44) Remove two nuts (55), two lock-
(4), two ceramic posts (6), two fiber
washers (54), and relay K1 (52)
washers (7), switch S7 (3), and
from relay bracket (53).
switch S6 (5).
(45) In the same manner as given in (44)
(33) Remove switch S4 and S5 assembly
above, remove eight nuts (two 58,
(10 through 16) in same manner as
two 60, two 62, two 44), eight lock-
given in (32) above.
washers (two 59, two 61, two 63,
(34) Remove switch S2 and S3 assembly
two 45), and four relays 47, 49, 50.
(17 through 23) in same mariner as
51).
given in (32) above.
(46) Remove nut (42), lockwasher (43),
(35) Remove two machine screws (34),
and terminal (48) from relay bracket
two fiber washers (35), two ceramic
(53).
posts (37), two fiber washers (38),
(47) Push out feedthrouah terminal (46)
and switch S1 (36).
from relay bracket (53).
(36) Remove three machine screws (56),
b. General Reassembly Tehniques.
three lockwashers (57), relay bracket
(1) Inspection. Inspect all
retaining
(53), and three sleeve, nuts (two 64,
rings for their original shape and for
one 88).
proper closing; replace all defective
(37) Remove three machine screws (8)
retaining rings.
and three lockwashers (9), and re-
( 2 ) Locking screws.
Apply Glyptal
move solenoid L4 (66) from rear
(General Electric Co.) or equivalent
gear plate (31).
to the threads of all screws where no
(38) Remove nine machine screws (three
locking device is provided. The term
29, three 27, three 32), nine lock-
"glyp" included with the item num-
washers (three 30, three 28, three
ber indicates that Glyptal should be
33) from other three solenoids (79,
applied before mounting the screw.
107, 129), and remove solenoids..
Caution : Except for the ball bear-
(39) Remove four pawl spring guides (90
ings, keep all other items of the read-
93, 112, 120) from rear gear plate
out mechanism free of lubricant at
(31).
all times.
(40) Remove seven sleeve bearings (65,
71, 78, 95, 106, 114, 124) from real
(3) Lubrication. Lubricate the ball hear-
gear plate (31). Note that three
ings (173, 176, fig. 4-17) with 1
sleeve bearings (71, 95, 114) have a
drop of Lubricating Oil, Instrument
59
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals