|
|
TM 11-6623-2609-34
Table 3-3. Resistance and Continuity Tests-Continued
Normal indication
Isolating procedure
Point of measurements
Between test panel jack J19 and Short circuit ------------------------------ Check wiring between J19 and ground.
ground.
Between test panel jack J17 and Short circuit---------------------------------- Check wiring between J17 and
W1P2A-16.
W1P2A-16.
Between test panel jack J16 and Short circuit----------------------------------- Check wiring between J16 and
W1P2A-15.
W1P2A-15.
Between test panel jack J15 and Short circuit ------------------------------ Check wiring between J15 and
W1P2A-23.
W1P2A-23.
Check wiring between J14 and
Between test panel jack J14 and Short circuit--------------------------------
W1P2A-22.
W1P2A-22.
Between test panel jack J13 and Short circuit -------------------------------- Check wiring between J13 and
W1P2A-21.
W1P2A-21.
Between test panel jack J12 and Short circuit ---------------------------------- Check wiring between J12 and
W1P2A-28.
W1P2A-28.
Between test panel jack J11 and Short circuit ---------------------------------- Check wiring between J11 and
W1P2A-27.
W1P2A-27.
Between test panel jack J10 and Short circuit --------------------------------- Check wiring between J10 and
W1P2A-26.
W1P2A-26.
Between test panel terminal board Short circuit --------------------------------- Check wiring between TB1-3 and
TB1-3 and W1P2A-5 and W1P2A-6.
W1P2A-5 and W1P2A-6.
Between black alligator clip and W1P2A- Short circuit --------------------------------- Check wiring between black alligator
and W1P2A-2.
clip and W1P2A-1 and W1P2A-2.
With POWER CB circuit breaker at ON, This is forward-biased resistance of Check CR1, Ml, and wiring between
between alligator clip + 28V and
alligator clip +28V and W1P2A-3
CR2 and resistance of Ml. Resis-
W1P2A3 and W1P2A-4 (positive ter-
tance will vary with applied voltage.
and W1P2A-4.
minal of ohmmeter connected to alli-
gator clip).
With VHF COMM OFF-PWR switch at 0 ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . Check radio control switch S4 and
PWR, between W1P2A-9 and ground.
wiring between S4 and W1P2A9.
With VHF COMM OFF-PWR switch at Approximately 30 ohms . . . . . . . . Check radio control lamps DS3, DS4,
OFF, between TB1-4 and ground (pos-
and DS5, and intercom control
itive probe of ohmmeter to TB1-4).
lamps DS1 and DS2.
With VHF COMM OFF-PWR switch at Approximately 20 ohms. . . . . . . . .
Check radio control lamps DS1 and
PWR, between TB1-4 and ground
DS2 and switch S4.
(positive probe of ohmmeter to TBl-
4).
Between test panel jack J5 sleeve and 0 ohm ------------------------------------------- Check wiring between J5 and W1P2B-
W1P2B-29.
29.
Between test panel jack J5 tip and 0 ohm. . . . . . . . . . . . . . . . . . . . . . . . Check wiring between J6 and
W1P2B-28.
W1P2B-28.
Between test panel jack J6 and W1P2B- 0 ohm. . . . . . . . . . . . . . . . . . . . . . . . . . . Check wiring between J6 and
28.
W1P2B-28.
Between test panel jack J7 and W1P2B- 0 ohm . . . . . . . . . . . . . . . . . . . . . . . . Check wiring between J7 and
29.
W1P2B-29.
Between test panel jack J8 and W1P2B- 0 ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . Check wiring between J8 and
36.
W1P2B-35.
Between test panel jack J9 and W1P2B- 0 ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . Check wiring between J9 and
36.
W1P2B-36.
With AUDIO switch at ON, between Approximately 500 ohms . . . . . . . . . . . . Check radio control potentiometer R1
W1P2B-35 and W1P2B-36.
and wiring between W1P2B-35 and
W1P2B-36 and radio control.
With radio control and intercom control Approximately 150 ohms . . . . . . . Check radio control potentiometer R1,
VOL controls both fully clockwise, be-
intercom control, and wiring to J4.
tween test panel jack J4 tip and sleeve
contacts.
Between W1P2B-37 and W1P2B-39.
Approximately 10,000 ohms . . . . . . . Check test panel potentiometer RI and
wiring between R1 and W1P2B-37
and W1P2B-39.
3-4
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |