Quantcast CONTINUITY TEST - TM-9-2320-366-20-20993

 

Click here to make tpub.com your Home Page

Page Title: CONTINUITY TEST
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home
   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
WTEC III TRANSMISSION PUSHBUTTON SHIFT SELECTOR (TPSS) DISPLAYS MAIN CODE 42, 44, 45, 46, 66, AND/OR 69 AND ANY SUB CODE
Up
TM-9-2320-366-20-2 M1083 Series 5-Ton 6 x 6 Medium Tactical Vehicles (MTV) Manual
Next
WTEC III TRANSMISSION PUSHBUTTON SHIFT SELECTOR (TPSS) DISPLAYS MAIN CODE 42, 44, 45, 46, 66, AND/OR 69 AND ANY SUB CODE (cont)
TM 9-2320-366-20-2
CAUTION
Loose or dirty connectors may cause
intermittent loss of power to transmission
ECU and diagnostic codes to be logged.
Ensure that all connectors are clean and tight
before performing troubleshooting. Failure to
comply may result in incorrect test results.
Use care when testing electrical connectors.
Do not damage connector pins or sockets
with multimeter probes. Failure to comply
may result in damage to equipment.
NOTE
Inspect connector pins/sockets for damage,
corrosion, and serviceability. Check that
connector pins are not pushed back and
are capable of making good contact.
CONTINUITY TEST
(1) Remove two screws and washers from
front grille.
(2) Remove screw and washer from front
grille.
(3) Remove front grille from cab.
(4) Disconnect connector P119 from
connector J119.
(5) Remove kick panel (para 16-3).
(6) Disconnect connector clamp from
connector P114.
(7) Disconnect connector P114 from WTEC III
transmission ECU.
(8) Install jumper wire on connector J119 for
appropriate sub code. Refer to Table 2-35.
WTEC III Cab Transmission Harness
Transmission Solenoid Test Points.
(9) Set multimeter to ohms.
(10) Connect positive (+) probe of multimeter
to connector P114. Refer to Table 2-35.
WTEC III Cab Transmission Harness
Table 2-35. WTEC III Cab Transmission Harness
Transmission Solenoid Test Points.
Transmission Solenoid Test Points
(11) Connect negative (-) probe of multimeter to
connector P114 and note reading on
Connector P114
multimeter. Refer to Table 2-35. WTEC III
Sub
Jumper
Positive (+)
Negative (-)
Cab Transmission Harness Transmission
Code
Across
Probe
Probe
Solenoid Test Points.
(12) Connect negative (-) probe of multimeter to
12
J119M to J119B
P114-1
P114-4
all other sockets in connector P114, one at
13
J119Tto J119N
P114-2
P114-20
a time, and note reading on multimeter.
14
J119C to J119V
P114-5
P114-17
(13) Connect negative (-) probe of multimeter to
15
J119W to J119B
P114-1
P114-21
ground and note reading on multimeter.
16
J119U to J119N
P114-2
P114-6
(14) If continuity is not present, in step 11, or
21
J119F to J119H
P114-3
P114-22
continuity is present in step 12 or 13,
22
J119D to J119V
P114-7
P114-17
replace WTEC III cab transmission harness
23
J119P to J119S
P114-19
P114-23
(para 7-138).
(15) Remove jumper wire from connector J119.
24
J119J to J119B
P114-1
P114-8
(16) Connect connector P119 to connector
26
J119K to J119A
P114-19
P114-24
J119.
27
J119M to J119B
P114-1
P114-4
Change 2

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.