Quantcast CLUTCH PRESSURE TEST - TM-9-2320-366-20-20873

 

Click here to make tpub.com your Home Page

Page Title: CLUTCH PRESSURE TEST
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home
   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
WTEC II TRANSMISSION ECU PUSHBUTTON SHIFT SELECTOR (TEPSS) DISPLAYS MAIN CODE 53 AND ANY SUB CODE (cont) - TM-9-2320-366-20-20872
Up
TM-9-2320-366-20-2 M1083 Series 5-Ton 6 x 6 Medium Tactical Vehicles (MTV) Manual
Next
WTEC II TRANSMISSION ECU PUSHBUTTON SHIFT SELECTOR (TEPSS) DISPLAYS MAIN CODE 54 SUB CODE 01, 07, 10, 12, 17, 21, 23, 27, 32, 34, 43, 45, 54, 56, 65, 70, 71, 72, 80, 81, 82, 83, 85, 86, 92, 93, 95, 96, or 97
TM 9-2320-366-20-2
WARNING
Wear approved eye protection when performing
transmission pressure checks. If oil contacts eyes,
seek medical attention immediately. Failure to
comply may result in injury to personnel.
CLUTCH PRESSURE TEST
(1) Remove front and intermediate propeller
shafts (para 9-2).
(2) Position drain pan under pressure tap.
(3) Remove pressure tap plug and preformed
packing from off-going clutch indicated
by the sub code. Refer to Table 2-30.
Off-Going Clutch Pressure Tap. Discard
preformed packing.
(4) Connect tube to boss adapter, hose, and
pipe to tube adapter to clutch pressure
tap.
(5) Perform STE/ICE-R Test # 50 (TM 9-4910-
571-12&P).
(6) Start engine (TM 9-2320-366-10-1) and
run at idle.
(7) With parking brake applied, make shift
indicated by sub code while assistant
notes reading on STE/ICE-R.
(8) If off-going clutch pressure does not go
to 8 psi (55 kPa) or less when shift is
made, notify DS Maintenance.
(9) If off-going clutch pressure does go to
8 psi (55 kPa) or less when shift is made,
replace WTEC III TEPSS (para 8-2).
(10) Shut down engine (TM 9-2320-366-10-1).
(11) Remove pipe to tube adapter, hose, and
tube to boss adapter from clutch pressure
tap.
(12) Position preformed packing and pressure
tap plug in control valve module.
Table 2-30. Off-Going Clutch Pressure Tap
(13) Tighten pressure tap plug to 84-120
lb-in. (9-14 Nm).
Sub
Off-Going
(14) Remove drain pan under pressure tap.
Sub Code Meaning
Code
Clutch(s)
(15) Install front and intermediate propeller
shafts (para 9-2).
08
L-N1 Shift
C3
(16) Clear diagnostic codes (para 8-4).
18
1-N1 Shift
C1
28
2-N1 Shift
C1
& C4
29
2-N2 Shift
C1
38
3-N1 Shift
C1
& C3
39
3-N3 Shift
C1
48
4-N1 Shift
C1
& C2
49
4-N3 Shift
C1
& C2
58
5-N1 Shift
C2
& C3
59
5-N3 Shift
C2
68
6-N1 Shift
C2
& C4
69
6-N4 Shift
C2
78
R-N1 Shift
C3
99
N3-N2 or N2-N3 Shift
C2
& C4
Change 1

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.