 |
|||
|
|
|||
|
Page Title:
TRANSMISSION/TRANSMISSION CONTROLS ADAPTABILITY CHART |
|
||
| ||||||||||
|
|
 TM 9-2320-366-20-1
TRANSMISSION/TRANSMISSION CONTROLS ADAPTABILITY CHART (CONT)
(1)
(2)
(3)
Installed Controls or
Installed Transmission or
Required Modification
Controls Being Installed
Transmission Being Installed
(Refer to Section III)
WTEC II
TID 3
Install 31-pin connector, replace
(with 24-pin connector)
(transmission serial number
transmission internal wiring harness,
1
6510262117 and subsequent)
and reprogram WTEC II TEPSS.
WTEC II
PRE-ID w/ 24-pin connector
Install adapter cable assembly.
(with 31-pin connector)
(transmission serial number prior to
6510032369)
WTEC II
PRE-ID w/ 31-pin connector
No modification required.
(with 31-pin connector)
(transmission serial number
6510032369 to 6510090785)
WTEC II
TID 1
No modification required.
(with 31-pin connector)
(transmission serial number
6510090786 to 6510142171)
WTEC II
TID 2
Replace transmission internal wiring
(with 31-pin connector)
(transmission serial number
harness.
6510142172 to 6510262116)
WTEC II
TID 3
Replace transmission internal wiring
(with 31-pin connector)
(transmission serial number
harness and reprogram WTEC II
1
6510262117 and subsequent)
TEPSS.
WTEC III
PRE-ID w/ 24-pin connector
Install adapter cable assembly and ID
(with ECU manufactured prior to
(transmission serial number prior to
harness.
2
October 1999)
6510032369)
WTEC III
PRE-ID w/ 31-pin connector
Install ID harness.
(with ECU manufactured prior to
(transmission serial number
2
October 1999)
6510032369 to 6510090785)
WTEC III
TID 1
No modification required.
(with ECU manufactured prior to
(transmission serial number
2
October 1999)
6510090786 to 6510142171)
WTEC III
TID 2
No modification required.
(with ECU manufactured prior to
(transmission serial number
2
October 1999)
6510142172 to 6510262116)
1
WTEC III
TID 3
Reprogram WTEC III ECU or install
(with ECU manufactured prior to
(transmission serial number
new WTEC III ECU (P/N 12421787-
2
October 1999)
6510262117 and subsequent)
002).
WTEC III
PRE-ID w/ 24-pin connector
Install adapter cable assembly and ID
(with ECU manufactured after
(transmission serial number prior to
harness.
3
October 1999)
6510032369)
WTEC III
PRE-ID w/ 31-pin connector
Install ID harness.
(with ECU manufactured after
(transmission serial number
3
October 1999)
6510032369 to 6510090785)
WTEC III
TID 1
No modification required.
(with ECU manufactured after
(transmission serial number
3
October 1999)
6510090786 to 6510142171)
1
Reprogramming can only be accomplished by an authorized Allison Transmission distributor. You must provide the
transmission serial number of the transmission being installed to ensure correct reprogramming. If at a later time, an
earlier version transmission is installed in a WTEC II equipped vehicle, WTEC II TEPSS will require reprogramming
again.
2
Vehicle serial number 012477 and lower. Refer to Figure 1.
3
Vehicle serial number 012478 and higher. Refer to Figure 1.
K-2
Change 2
|
|
Privacy Statement - Press Release - Copyright Information. - Contact Us |
Click
here for thousands of PDF manuals