Quantcast Table 2-12.4. M1085/M1086/M1089/M1096 Intermediate, Side, and Rear Marker Light Connectors and Splices

 

Click here to make tpub.com your Home Page

Page Title: Table 2-12.4. M1085/M1086/M1089/M1096 Intermediate, Side, and Rear Marker Light Connectors and Splices
Back | Up | Next

Click here for thousands of PDF manuals

Google


Web
www.tpub.com

Home
   
Information Categories
.... Administration
Advancement
Aerographer
Automotive
Aviation
Construction
Diving
Draftsman
Engineering
Electronics
Food and Cooking
Logistics
Math
Medical
Music
Nuclear Fundamentals
Photography
Religion
   
   

 

Share on Google+Share on FacebookShare on LinkedInShare on TwitterShare on DiggShare on Stumble Upon
Back
M1085/M1086/M1089/M1096 INTERMEDIATE, SIDE, AND/OR REAR MARKER LIGHT(S) DO NOT ILLUMINATE (cont) - TM-9-2320-366-20-11022
Up
TM-9-2320-366-20-1 M1083 Series 5-Ton 6 x 6 Medium Tactical Vehicles (MTV) Manual
Next
M1085/M1086/M1089/M1096 INTERMEDIATE, SIDE, AND/OR REAR MARKER LIGHT(S) DO NOT ILLUMINATE (cont) - TM-9-2320-366-20-11024
TM 9-2320-366-20-1
WARNING
Remove rings, bracelets, watches, necklaces,
and any other jewelry before working around
vehicle. Jewelry can catch on equipment and
cause injury or short across electrical circuits, or
cause severe burns or electrical shock.
CAUTION
Use care when testing electrical connectors not
to bend connector pins or damage connector
sockets with multimeter probes. Failure to
comply may result in damage to equipment.
NOTE
Inspect connector pins/sockets for damage,
corrosion, and serviceability. Check that
connector pins are not pushed back and
are capable of making good contact.
VOLTAGE TEST
(1) Disconnect marker light connector from
connector (refer to Table 2-12.4. M1085/
M1086/M1089/M1096 Intermediate, Side,
and Rear Marker Light Connectors and
Splices).
(2) Set multimeter to volts DC.
(3) Connect positive (+) probe of multimeter
to connector (refer to Table 2-12.4.
M1085/M1086/M1089/M1096
Intermediate, Side, and Rear Marker Light
Connectors and Splices).
(4) Connect negative (-) probe of multimeter to
ground.
(5) Position main light switch to SER DRIVE
(TM 9-2320-366-10-1) and note reading
on multimeter.
(6) Position main light switch to OFF
(TM 9-2320-366-10-1).
(7) If 12 VDC is not present, repair wire 489
(refer to Table 2-12.4. M1085/M1086/
M1089/M1096 Intermediate, Side, and
Rear Marker Light Connectors and Splices)
Table 2-12.4. M1085/M1086/M1089/M1096 Intermediate,
(para 2-45) or replace M1086/M1089 rear
Side, and Rear Marker Light Connectors and Splices
lights cable assembly (para 7-104) or
M1085/M1096 rear lights cable assembly
M1085/M1086
(para 7-84).
Marker Light
Connector
M1089 Splice
/M1096 Splice
LH Intermediate
P94
Splice E64
Splice
E49
LH Side
P85
Splice E16
Splice
E51
LH Rear
P86
Splice E16
Splice
E51
Left Rear
P54
Splice E15
Splice
E50
Middle Rear
P56
Splice E15
Splice
E50
Right Rear
P58
Splice E15
Splice
E50
RH Rear
P89
Splice E17
Splice
E52
RH Side
P88
Splice E17
Splice
E52
RH Intermediate
P95
Splice E64
Splice
E49
Change 1

Privacy Statement - Press Release - Copyright Information. - Contact Us

Integrated Publishing, Inc.